Sponsored Links

Archives

October 2006
M T W T F S S
« Sep   Nov »
 1
2345678
9101112131415
16171819202122
23242526272829
3031  

Butter Cookie

That is the name of the color.
Buttercookie
The archways and ceiling trim are Redwood, stained sealed and applied.
I know that the archways are going to take a beating, as redwood is soft. But it looks good now.

What do you mean it’s a different White?

While I am looking for color advice for the walls in my living room, I have made a design choice regarding my ceiling. It is going to be White. I am using Home Depot’s BEHR No. 558 Ultra White Ceiling Paint in a flat finish.

As you can see there are many shades of white. Where I have cut in is the Ceiling white. The previous wall and ceiling color was Glidden Professional Finish Ultra Build White, which in my opinion fails on all counts as a rolling paint. It has a gray tinge, it is a thin paint, doesn’t roll well, and requires at least 2 coats to cover. May work okay in a spray gun, but I don’t use them.

Home Depot’s Behr Brand is really great paint. It has good body, lays down well, and when properly applied covers in one coat. I haven’t used any other paint since my first can. Worth every cent you pay for it. And a lot of times it goes on sale making it an even better value.
Highly Recommended.

Orphan Tools - Basin Wrench

When you are confronted with the prospect of replacing a faucet, you need a basin wrench.

Basin Wrench
It has a spring loaded jaw, a swivel head and a sliding ‘T’ handle. All which are necessary to get this tool to do it’s job.

In the world of remodeling and home repair there are a lot of tools you need, tools you want, and tools that have a single purpose in life that you hope that you never have to add to your tool set.

The basin wrench is one of these. It has only one purpose. It tightens or loosens the nuts that attach the top of your water supply lines to the bottom of your faucets.
As you can see, the space you have to work with is very small, and no amount of cursing, or any other tool will fit into this space.

basin wrench at work
There is an alternative. In the case of drop in sinks or small vanity tops, you disconnect the supply lines just north of the shutoff valves, and the drain line at both sides of the ‘P’ trap, and remove the sink entirely from the cabinet or countertop. You can turn it over and reach everything to replace your faucets.

This has it’s perils, if you have a cast iron sink, or a one piece counter and sink arrangement. The bathroom sinks are not too bad to do this way. The kitchen sink with a garbage disposal adds another level of complexity to the mix.

You will probably need a basin wrench.

Living Room Archways

Like most folks, a lot of remodeling projects are time and money deals. There is never enough of both. Since I didn’t win the lottery last night, and I am waiting for some daylight, an update on the casa lemurzone is called for.

The livingroom is currently the largest room in my house and the least used room. After the soffit adventure and the racetracking, I spent a lot of time with other projects and work for other folks. Computers, Networking, Data Recovery, and some painting projects.

The kitchen is a mess in terms of lack of storage, layout, and my appliances. I want a lot more storage, new cabinets, and more room.

So to get more storage in the kitchen, I am narrowing the archway between the kitchen and the living room. The archway is 10” wide as the wall between the kitchen and the living room is one of the original concrete block walls. The house was built in 1954 and concrete block was the building material of choice for the houses in this neighborhood.

On the top of the photo you can see the soffit and racetracking from the living room adventure. The archway is 48” wide. I am cutting that down to 37”. This will give me a 10” deep pocket on the kitchen side for some built in cabinets and storage. On the left side of the kitchen next to the original exterior door is a light switch that currently controls the lighting that was on the carport, which is now enclosed and the backyard light. I will be building a 2×4” wing wall right on top of that switch and moving it 90 degrees and installing it on the doorway side of that wing wall. This will give me almost 4′ to build storage cabinets.

The framing is in and the drywall is up. For the detail folks, the front of the arch is 2×4 lumber giving me a solid outside corner for nailing the drywall and attaching the cornerbead. On the wall side I used steel studs screwed to the wall side of the arch as it was easier and quicker. It also allowed me to ignore the elevation change on the recess of the original archway. I used drywall screws for the drywall and the corner bead. One was I had no drywall nails handy and the second and more important reason is that outside corners always take a beating. I did also remove the ceramic tile below this as at some point I will be replacing the flooring.

The corner bead is up and the taping is in progress. As you see, I am taping one side of the angles at a time. This will give you a much nicer job especially if you are doing drywall taping for the first time.

The inside of the arch has its first coat and the wall side of the inside corners are coated.

The top of the arch and the bottom of the soffit were designed to allow me to run a band of 3” redwood trim around the perimeter of the room, ala Craftsman style. Unlike a lot of my remodeling projects, there is an endgame here. This band will tie the room together despite the difference in elevation between the soffit bottom and the living room ceiling. It also lets me catch the top of the windows and the top of the doorways.

Here is the archway on the kitchen side. On the left is a line which will be the extention of the kitichen cabinet soffit, which will be made wider to extend the HVAC across the hallway into the laundry room, like I did with the living room. Having HVAC in a room makes it ‘livable’ space for the purposes of resale.

I mentioned before that soffit’s were for the most part badly built boxes to make cabinets look good. However on the plus side, soffit’s lower the amount of cubic space that you are heating and cooling.
My house will be a blend of Art Deco, Arts and Crafts, and Japanese influences. The Japanese influence will be mostly in the pocket doors that I will be replacing a lot of the current hinged doors with. When you only have 818 square feet of livable space, giving up 9 square feet on the floor and 24 square feet on the wall is not my idea of a good time.